Intimus 120 CC4 Bedienungsanleitung PDF herunterladen (Seite 6)

The shredder may not be used as a

step ladder or as a seat. Danger of

falling due to breakage!

SWITCHING THE MACHINE ON:

Proceed as follows to switch the machine to

“Ready”:

- Press the function button (2) briey.

- The function button (2) LED display comes

on for “Ready”.

- The machine can be loaded.

MATERIAL FEED:

Feed paper into the cutting mechanism through

the paper feed slot (12) (g. 3).

Feed data carriers (CD, DVD or credit card)

into the cutting mechanism individually into the

separate CD/DVD feed slot (13) (g. 3).

The machine automatically switches to forwards

running, draws the material in and automatically

switches off after shredding.

When shredding papers, do not shred

CD/DVD at the same time, and vice

versa!

Note: For shredding transparent lms, the

machine must be manually switched to forwards

running (press and hold the forwards button (3)

for approx. 2 secs.).

By briey pressing the function button (2) (Stop

function), the shredding process can be stopped

at any time. To continue, press and hold the

forwards button (3) for approx. 2 secs.

If the machine is not used for a period of approx.

5 mins., it automatically switches off.

Never feed the shredder with a

quantity of material exceeding the

maximum indicated. Refer to the

TECHNICAL DATA section!

Should the machine become

overloaded, follow the instructions under

“MATERIAL JAM IN MACHINE” under

“MALFUNCTIONS”.

Two separate collection containers ensure

that waste is separated properly.

EMPTYING THE PAPER COLLECTION BAG

(Fig. 4):

If the paper collection bag is full the machine

switches off. The control display (11) comes

on. Proceed as follows:

- Open the door. The control display (8)

comes on. If there is still material in one of

the feed slots, the control display (6) also

comes on.

- Take the collection bag (14) and the frame out

of the bottom part of the housing. Remove the

bag and dispose of the contents. The control

display (11) goes out.

CONTROLS:

7 = Control display (Fig. 1)

“Oil cutters”

Comes on when the cutters in the cross

cut version must be oiled. The lubrication

procedure must be acknowledged on

the reverse button (4) (see description in

“CUTTER MAINTENANCE”).

8 = Control display (Fig. 1)

“Door open”/ “Door malfunction”

a) “Door open”

Comes on if the door on the lower part

of the machine is opened. The machine

switches off automatically and cannot

be started as long as the door remains

open.

b) “Electrical fault”

Flashes when there is an electrical fault

in the door sensor. The machine switches

off. Please contact your dealer.

9 = Control display (Fig. 1)

“Motor overload” /

“Electrical fault”

To nd out what to do see the relevant

description under the “MALFUNCTION”

section.

a) “Motor protection”

Comes on when the motor has been

overloaded and has switched off. The

machine cannot be started while the

motor is cooling down.

b) “Electrical fault”

Flashes when there is an electrical fault

inside the control board. At the same

time the function button (2) LED display

ashes. The machine switches off.

Please contact your dealer.

10 = Control display

“CD/DVD container full” (Fig. 1)

Comes on when the CD/DVD container is

full and must be emptied. The cutting unit

for reducing CD/DVD switches off. The

emptying procedure must be acknowledged

on the forward button (3).

Note: The cutting unit for reducing paper

can be used furthermore.

11 = Control display

“Paper collection bag full” (Fig. 1)

Comes on when the paper collection bag is

full and must be emptied. The cutting unit

for reducing paper switches off.

Note: The cutting unit for reducing CD/

DVD can be used furthermore.

12 = Paper feed slot (Fig. 3)

13 = CD/DVD feed slot (Fig. 3)

14 = Paper collection bag (Fig. 4)

15 = CD/DVD collection container (Fig. 4)

16 = Oil reservoir (Fig. 6)

- Fit the emptied bag onto the bag frame and

insert the bag and the frame into the bottom

part of the housing again. Close the door. The

control display (8) goes out.

- If the control display (6) comes on, press

the forward button (3) briey. The remaining

material in the feed slot is shredded and the

display go out.

Note: The machine will only run if the door is

closed.

EMPTYING THE

CD/DVD COLLECTION CONTAINER (Fig. 4):

Note: The “CD container full” is monitored by

counting the number of shredding processes

performed.

If the number of CD’s/DVD’s pre-programmed

into the control unit (about 20) is shredded the

machine switches off. The control display

(10) comes on.

Proceed as follows:

- Open the door. The control display (8)

comes on and the forward button (3) LED

display as well as the control display (10)

ashes.

- Remove the collection container (14) from

the inside of the door and dispose of the

contents.

- Press the forward button (3) briey to

acknowledge that the CD/DVD container has

been emptied. The counting process begins at

zero again. The control display (10) and the

forward button (3) LED display go out.

- Attach the emptied container to the door again

and close the door.

Note: The machine will only run if the door is

closed.

DYNAMIC LOAD DISPLAY:

To prevent a material jam and thus ensure

a continual, effective destruction of the data

carriers, the current load level of the motor is

displayed during the shredding process by a

coloured, diffuse light in the feed slot as follows:

Green light: load < 50%

Yellow light: load 50 - 75%

Red light: load 75 - 100%

120SC2

120CC3

120CC4

120CC5

120CC6

90134 9 08/13

OPERATION

g. 1 g. 3 g. 4

Translation of the Original Operation Manual

Übersetzung der Originalbetriebsanleitung

1 2 3 4 5 6 7 8 9 10 11 ... 55 56

Kommentare zu diesen Handbüchern

Keine Kommentare

Intimus 120 CC4 Bedienungsanleitung Seite 6

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Aktenvernichter Intimus 120 CC4